The Audison Prima AP8.9 bit amplifier is an 8 channel amplifier that has a built in digital signal processor (DSP). The 8 channel amplifier configuration allows you to power a dual dash speaker, the kick panel speakers, rear 6x9's, and you bridge the 7th and 8th channels to power the subwoofer. The DSP allows you full control over your vehicle's sound system. The digital processor that is built into this amplifier allows you to plug a laptop into the amp, and you can tune each speaker independently with full equalization. This allows you to dial in each speaker individually so that you can have it play the frequencies it was designed for, at the level that sounds correct to you. The DSP flattens the input signal from the radio, removing any built-in equalization. Once the input signal is flat, you use the software to configure your front speakers, configure your rear speakers, and then tell the software the subwoofer setup you have, and configure it. Then, speaker by speaker, you can adjust the frequencies and the amplifier gain for each channel independently. This allows you to set your front dash speakers to play just the frequencies you want them to, at the level you want them at. Same thing with your rear speakers. Same thing with your subwoofer. You have full control. Think of a DSP as the soundboard at a concert. You are the sound man and you get to tune your stereo so that it sound exactly the way you want it to. When you go see good live musicians in small, intimate venues, the reason it sounds so good is because DSP's are involved.
If you want to have a dash speaker, or center channel speaker, a pair of front speakers, a pair of rear speakers, and a subwoofer, this is the amplifier for you. The DSP will allow you to dial in each speaker individually so that you have the ultimate sound stage and audio experience in your vehicle.
Now let's get to the power aspect of this amplifier. The Audison AP8.9 bit amplifier, the 540W from the drop down, is rated at 35W x 8 at 4 ohms, 65W x 8 at 2 ohms. The 1040W 8 channel amplifier is rated at 85W x 8 at 4 ohms. Now, if you are thinking to yourself, "But, my radio says that it is putting out 45 watts a channel for my front speakers," that isn't necessarily an apples to apples comparison. Even an amplifier that is rated at 75W RMS per channel is not an apples to apples comparison. Because of the built-in DSP, you can adjust the gain on the amp for those front speakers, +/- 12dB, which will allow them to play 16 times louder. Also, if you are actively crossing them over, you are selecting the level at each frequency, allowing you to completely dial in those front speakers. You can set it up so that the front speakers are not playing any mid-bass that they can't reproduce. 35 watts RMS from this amp will blow away 50-75 watts RMS from another without a DSP. For the rear speakers, the 35 watts RMS is plenty because once again, you can control the gain and frequency level of each speaker. Finally, for the subwoofer, you will want to bridge channels 7 & 8 so that they put out 130 watts at 4 ohms. This amount of power will still give you plenty of bass if you select the correct subwoofer for it. The Audison Prima 8" is a perfect fit, as is the JL Audio 8W3v3-4 or the 8W1v3-4. The other option is to use the RCA pre-out on the amplifier to connect to a separate monoblock amp, and have that amp power the subwoofer. The DSP will still control that output, you will just want to make sure that you are not using any of the built in signal processing on the mono amp.
If you like clean, well balanced, and are all about sound quality, this Audison 7 speaker package is the way to go. We recommend going with the 1040 watt amplifier. This is not an inexpensive package, if you are thinking about it, the extra $500 is worth it
If you are concerned about setting everything up, Audison offers a full tutorial on their YouTube channel and we can help guide you through it. We can show you settings that have worked for other vehicles so that you have a good benchmark as to where you start.