JL Audio 10" W6 HO110-W6v3 with XD600/1v2 10 Inch 600 Watt Subwoofer Kit

This kit includes the JL Audio HO110-W6v3, 10 inch W6v3 loaded enclosure, an XD600/1v2, 600-watt monoblock amplifier, a 4 AWG amp wiring kit with an RCA cable, and 15 feet of 12 AWG speaker wire.

JL Audio H0110-W6v3 10 Inch W6 Loaded Enclosure

The HO110-W6v3 is a ported, loaded enclosure with a 10" W6v3 subwoofer that has been wired to a 2 ohm load. The subwoofer comes pre-installed and wired to a 5-way binding post terminal on the side of the enclosure. The 10" W6v3 subwoofer handles 600 watts RMS and has dual, 4 ohm voice coils. The chamber-coupled, ported enclosure is designed and optimized by the team at JL Audio for maximum performance from the W6 subwoofer.

The JL Audio 10W6v3 subwoofer is amazing. There are many people that actually prefer the W6 to the W7 because it is punchier, with more of that kickdrum-to-the-chest type output. Sure, the W7 will go lower and is more accurate that the W6, but W6 is tightier and punchier whereas the W7 is boomier and more rolling. JL's High Output enclosures are designed to not only hit hard, but to also sound really good. The chamber-coupled port design of this enclosure wraps around the inner walls of the box to couple the port output with the direct output from the subwoofer. The box has been tuned in real world, listening environments to provide the optimum volume, port length, and port diameter for the 10W6 subwoofer. If you aren't installing a W6 in a custom enclosure, do yourself a favor and get the HO110-W6v3. This enclosure sounds too good and you don't have to deal with the installation of the woofer itself. Connect it to your amplifier and you are good to go, knowing that you have the best box in the world for this subwoofer.

JL Audio XD600/1v2 600 Watt Monoblock Amplifier

The JL Audio XD600/1v2 amplifier delivers 600 watts RMS at 2 ohms, which is a perfect match for the W6 which is rated to handle up to 600 watts RMS.

The JL Audio XD600/1v2 uses JL's NexD switching technology and uses JL's advanced thermal rollback technology. This helps keep the amp cooler and therefore it sounds better and has less distortion. The XD600/1v2 amplifier is very compact given it's output and performance. The XD series amplifiers are the "go-to" amps among the JL reps. The XD600/1v2 accepts both high and low level inputs and has selectable 12dB or 24 dB/octave crossovers with a defeatable low-pass filter.

To quickly and easily adjust the bass level for each song and recording, don't forget to add the HD-RLC bass knob.

4 AWG Amp Wiring Kit + Speaker Wire Included

We include a 4 AWG amp wiring kit with a 17 foot RCA cable and 15 feet of 12 AWG speaker wire with this subwoofer kit. The wire used in both the amp kit and the speaker wire is the good stuff. We only use 100% oxygen-free copper to ensure maximum power from the amplifier and output from the subwoofer. It makes no sense to spend the money on high quality JL Audio components only to starve them with cheap wire that doesn't transmit the power properly.

Bass Knob Recommended

We recommend adding the JL Audio HD-RLC bass knob to your subwoofer kit. Every song has different levels of bass. Some have a ton of bass while the next song may have no bass at all. Adding a bass knob allows you to quickly and easily turn the bass up or down to meet your listening preferences. In addition, if a song has too much bass and distortion, the bass knob allows you to turn it down quickly, without having to fumble with your head unit. The bass knob not only provides a better listening experience but it also helps protect your investment from unwanted distortion.

Straightforward Wiring to a 2 Ohm Load

The loaded enclosure comes pre-wired to the terminal post on the outside of the enclosure. Connect positive on the amplifier to positive on the enclosure and do the same thing with the negative terminals. This will wire the subwoofer to a 2 ohm load and ensure that you get the full 600 watts RMS from the XD600/1v2 amplifier. Please refer to the diagram below.